Hạt nhựa nylon 6 chống cháy PA6 GF40 FR

PA6 GF40 FR is a flame-retardant nylon 6 compound reinforced with 40% glass fiber, supplied as injection-molding pellets. The reference grade on this page is PA6 WHRG40A.

Ứng dụng: Connector housings, switch housings, terminal blocks and reinforced appliance parts.

Cấp độ tham chiếu: PA6 WHRG40A; use the exact suffix when comparing data or requesting material.

Flame requirement: The supplier sheet lists V-0; confirm specimen thickness and the required test record.

Để nhận báo giá: Send the drawing or application, wall thickness, color, quantity and destination.

Danh mục: ,

PA6 GF40 FR Material Overview

PA6 GF40 FR is a flame-retardant nylon 6 compound reinforced with 40% glass fiber, supplied as injection-molding pellets. The reference grade on this page is PA6 WHRG40A.

Mặt hàng Chi tiết
Polymer PA6 (nylon 6)
Cốt thép 40% sợi thủy tinh
Cấp độ tham chiếu PA6 WHRG40A
Biểu mẫu Viên nén
Chế biến Đúc phun; xác nhận hướng dẫn về loại vật liệu hiện tại

Tính chất của vật liệu tham chiếu

Cấp độ tham chiếu: PA6 WHRG40A. Các giá trị này áp dụng cho mã tham chiếu nhà cung cấp được nêu, chứ không phải cho mọi công thức trong nhóm vật liệu.

Tài sản Giá trị điển hình Đơn vị Phương pháp thử nghiệm
Độ bền kéo 150 MPa ISO 527-2
Độ biến dạng kéo tại điểm đứt 8 % ISO 527-2
Mô-đun uốn 9000 MPa ISO 178
HDT, phương pháp B 186 °C ISO 75-2/B
Độ đặc 1.60 g/cm³ ISO 1183
Sự co ngót khi đúc 0.4 % ISO 2577

These typical values belong specifically to PA6 WHRG40A. Specimen conditioning and flame-test thickness are not stated in the supplied sheet. Confirm the current revision and the required test conditions before approval; HDT is not a continuous service-temperature rating.

Download PA6 WHRG40A supplier reference datasheet (PDF)

PA6 GF40 FR Applications

PA6 GF40 FR nine illustrative application examples
Các ứng dụng minh họa; hãy xác nhận loại vật liệu đã chọn cho chi tiết của bạn. Nhấn vào hình ảnh để phóng to.

Connector housings and terminal blocks.

Consider this compound for rigid housings around terminals and fasteners. Check pin retention, thin sections, weld lines and the electrical requirements for the selected grade.

Switch, relay and control housings.

Ribs, snap features and screw bosses need stiffness without brittle failure during assembly. Agree the flame standard and specimen thickness, then validate production-tool samples.

Motor, appliance and fan structures.

Review heat exposure, vibration, inserts and critical fits. The reinforcement can influence shrinkage and direction-dependent properties, so check the molded component rather than relying on test-bar data alone.

Xử lý và kiểm tra chi tiết

Follow the WHRG40A drying and molding instructions. Review gates, weld lines, glass-fiber orientation, tooling wear and moisture conditioning. Confirm the required flame performance on the exact production formulation and thickness.

Đối với các bộ phận đã hoàn thiện, hãy tiếp tục ép phun. Để so sánh các nhóm vật liệu, hãy xem lại dòng sản phẩm nhựa kỹ thuật.

Cung ứng nguyên vật liệu và hỗ trợ sản xuất

Nhựa nylon kết nối nguồn cung cấp nhựa kỹ thuật với dịch vụ gia công theo yêu cầu. WANHAN là nhà máy sản xuất dược phẩm hợp tác với chúng tôi; những bức ảnh dưới đây cho thấy thiết bị cấp nguyên liệu, quy trình đùn và phòng thí nghiệm của nhà máy.

Thiết bị cấp nguyên liệu tại WANHAN, nhà máy hợp tác của Nylon Plastic
Cấp liệu
Các sợi nhựa đùn tại nhà máy liên kết của WANHAN
Quy trình đùn
Khu vực làm việc trong phòng thí nghiệm tại nhà máy hợp tác của WANHAN
Phòng thí nghiệm

Lựa chọn cấp độ và công thức

Hãy cho chúng tôi biết cấp độ hiện tại, ứng dụng và điều kiện vận hành của quý vị. Chúng tôi sẽ phối hợp việc xem xét vật liệu và xác định bảng thông số kỹ thuật phù hợp với công thức được đề xuất.

Các tài liệu chất lượng cho đơn hàng của quý khách

Hãy nêu rõ các tài liệu TDS, hồ sơ lô hàng, yêu cầu kiểm tra hoặc các tài liệu tuân thủ mà đội ngũ mua hàng của quý vị cần. Các tài liệu và tiêu chí chấp nhận đã được thống nhất đối với vật liệu được báo giá.

Dịch vụ hỗ trợ ngoài lĩnh vực hạt nhựa

Đối với một chi tiết hoàn thiện, cần kết hợp việc lựa chọn vật liệu với thiết kế chi tiết, dụng cụ gia công và quá trình kiểm tra khuôn đúc. Hãy bắt đầu từ bản vẽ, số lượng dự kiến và các kích thước quan trọng.

Chứng chỉ Hệ thống Quản lý Nhà máy Hợp tác

Các chứng chỉ ISO 9001, ISO 14001 và ISO 45001 được cung cấp xác nhận rằng Quảng Đông Wanhan với tư cách là đơn vị được chứng nhận. Phạm vi hoạt động của họ bao gồm hạt nhựa đã qua xử lý và các hoạt động quản lý liên quan; tiêu chuẩn này không chứng nhận mọi loại vật liệu hay mọi dịch vụ gia công sản phẩm hoàn thiện.

Rà soát năng lực sản xuất và hồ sơ chất lượng. Để phê duyệt tài liệu, cần đảm bảo sự khớp nhau giữa pháp nhân, phạm vi chứng nhận và cấp độ được ghi trong báo giá.

Câu hỏi thường gặp

What is PA6 GF40 FR?

It is nylon 6 reinforced with 40% glass fiber and formulated for flame-retardant applications. This page uses PA6 WHRG40A as its specific supplier reference.

Which applications are candidates for this material?

Connector bodies, terminal blocks, switch and relay housings, control enclosures and reinforced appliance structures are candidates. Each component needs a review of load, heat, electrical spacing and assembly requirements.

Does the V-0 listing certify my finished component?

No. The supplier sheet lists V-0 without specifying the test thickness. Request the applicable report and verify the exact formulation, color and thickness required for the part; the finished assembly may require separate qualification.

Can I use WHRG40 data for WHRG40A?

Do not assume that a similar code means identical material data. Use the WHRG40A sheet linked here and have the exact grade suffix confirmed on the quotation and supplied material.

Does the 186°C HDT define continuous operating temperature?

No. HDT under ISO 75-2/B is a laboratory deflection result. Long-term heat exposure, load, moisture and part geometry need separate assessment.

What should I include in an inquiry?

Send the application or drawing, minimum wall thickness, flame and electrical standards, operating conditions, color, quantity and destination. Identify any current grade that the new material must replace.

Yêu cầu thông tin về vật liệu và báo giá

Vui lòng gửi bản đề xuất hoặc bản vẽ, cấp độ hiện tại, điều kiện sử dụng, màu sắc, số lượng và điểm đến. Vui lòng nêu rõ các phương pháp thử nghiệm, tài liệu và tiêu chí chấp nhận cần thiết để vật liệu được đề xuất có thể được đánh giá phù hợp với dự án.

Request PA6 WHRG40A TDS and Quote

Cuộn lên đầu trang

Liên hệ với chúng tôi

Vui lòng điền vào biểu mẫu bên dưới, và chúng tôi sẽ liên hệ với bạn trong thời gian sớm nhất.

Thông tin liên hệ